Copper Coast Development Plan 2017

 

Copper Coast Development Plan 2017

In South Australia, the Development Act 1993 and Development Regulations 2008 provide the framework to development and building work to which Development Plans were established as the primary legal document to guide new development in each South Australia local government region. 

The Development Plan for each council area contains the:

  • zones, maps and rules that guide and control what can / cannot be undertaken on any piece of land within its jurisdiction
  • objectives, principles and policies that will control and affect the design and locaiton of proposed land use activities
  • desired character for a given area or zone
  • allowed land uses and those that are not contemplated within a zone
  • basis upon which applications for new development will be assessed
  • appeals decision process. 

How do I Access a Development Plan

Development Plans for all Councils within South Australia are available online free of charge - www.sa.gov.au website
 
Click on the icon below to access the Copper Coast Council Development Plan:
 

Development PlanCopper Coast Development Plan 2017

 

 

How do I use the Development Plan?

Using the Development Plan

The following basic steps are suggested to assist users to navigate through a Development Plan. 

Step 1    Determine what Zone (Precincts and Policy Areas) the land is located within
  • Maps detailing the location and boundaries of specific Zones and Precincts/Policy Areas appear at the back of the Development Plan.  An index of maps will appear at the front of the Zoning Maps section.
  • Refer to the Index to Zones Map (using the Table of Contents at the front) and find the specific Zone Map for the general locality of the property
  • From the Zone Map, locate the property and hence the zone in which it is situated
  • If there is a policy area within the zone, reference to this is shown on the zone map, so look carefully
  • Check through the Development Plan to identify if there are any overlay-type maps that introduce particular policy (eg watershed, flood or bushfire protection areas)
  • From the Table of Contents, find the pages in which the policies for that particular zone (and policy area if applicable) are located
  • These maps also identify a number of development constraints such as heritage, natural resources, etc.
Step 2    What does the Zone (Precincts and Policy Areas) provisions say?
  • Carefully read the Zone provisions (and Precincts and Policy Areas if applicable) as these will describe what can be done with the land and will in most cases set out what uses may be allowed and what are unacceptable
  • Read also and consider if your development will be consistent with the Desired Character Statement for the zone (if there is one)
  • Have a very close look at the list of non-complying kinds of development to make sure the development does not fall within that list - where a land use or activity is defined as ‘non-complying’, it will generally not be granted consent (this is because it is a kind of development that is considered inappropriate in that zone)
  • If a development application is listed as ‘complying’, consent will be granted provided that the application meets all the standards for complying development, usually listed as a Table in the Development Plan  Note: you should also check Schedule 4 of the Development Regulations to check if the development is complying.
  • If the development is not listed on either the complying or non-complying lists, then this type of development is referred to as a ‘merit’ (or ‘consent’) development, which then requires an assessment against all relevant provisions of the Development Plan (those in the Zone and those in the General/Council wide section – see step 3).
Step 3    Consider all relevant General/Council wide policies
  • If the Zone (and Policy Area and Precinct if applicable) suggests the development is possible, you will need to refer to the General/Council wide policies for an idea of the development standards that may apply to the particular type of use or building you are looking at
  • Essentially, the Zone policies give you an idea of what can be built and where it can be built and the more broad General/Council wide policies establish how that development should proceed
  • It is common for the General/Council wide policies to be set out under various topic headings and many of these will be relevant, some in a general sense and others in a more detailed way.
Step 4    Form an opinion about the development
  • Having done the above you should be able to get a feel for whether a proposed development is likely to be appropriate or not and to identify what matters need further detailed consideration to determine if the proposal will be acceptable.

Important Points to Note

  • Procedures are all-important – make sure you get the procedural requirements right in dealing with the application
  • Remember that reference needs to be made to all parts of a Development Plan to get a full appreciation of the relevant policies that apply to any site or to a particular form of development
  • You must assess development applications giving consideration to all relevant provisions of the Development Plan and make a judgement, on balance, having regard for all relevant provisions, the acceptability or otherwise of a development proposal
  • The policies in the Development Plan are advisory in nature, not mandatory (note the near exclusive use of the word ‘should’ not ‘must’), and therefore must be weighed up one against the other as to their relevance and applicability to a particular proposal.
 

Contact Council

Find Us

51 Taylor Street

PO Box 396

Kadina SA 5554

Opening Hours

Monday to Fridays

9.00am - 5.00pm

Closed Public Holidays

Subscribe with us

Subscribe
Top